code:json
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
code:json [2016/11/28 02:35] – added information on a couple more commands jtello | code:json [2017/01/20 12:04] – added devices types jtello | ||
---|---|---|---|
Line 3: | Line 3: | ||
|change_constraints|change_script|[[# | |change_constraints|change_script|[[# | ||
- | |cnst_time|consts|create_target|dec|devbytype| | + | |cnst_time|consts|create_target|dec|[[#devbytype]]| |
|deviceinfo|[[# | |deviceinfo|[[# | ||
- | |hasimage|inc|labellist|labels|lastimage| | + | |hasimage|inc|labellist|labels|[[#lastimage]]| |
|messages|night|obytid|plan|runscript| | |messages|night|obytid|plan|runscript| | ||
- | |satisfied|script|selval|[[# | + | |satisfied|script|selval|[[# |
|sunalt|taltitudes|tbydistance|tbyid|tbylabel| | |sunalt|taltitudes|tbydistance|tbyid|tbylabel| | ||
|tbyname|tbystring|tlabs_add|tlabs_delete|tlabs_set| | |tbyname|tbystring|tlabs_add|tlabs_delete|tlabs_set| | ||
|[[# | |[[# | ||
+ | Info about them can be figured out from the relevant code: | ||
+ | [[https:// | ||
+ | [[https:// | ||
====== cmd ====== | ====== cmd ====== | ||
Line 20: | Line 23: | ||
note the URL code %20 is used to pass on the space between the command and the parameters. | note the URL code %20 is used to pass on the space between the command and the parameters. | ||
+ | |||
+ | ====== devbytype ====== | ||
+ | This will list the devices by type with the modifier being an interger t: | ||
+ | for example: | ||
+ | http:// | ||
+ | will output mounts attached to this rts2 instance. | ||
+ | Where the differt device types are: | ||
+ | |1|SERVERD|9|GRB|21|IMGPROC| | ||
+ | |2|MOUNT|10|FOCUS|22|SELECTOR| | ||
+ | |3|CCD|11|MIRROR|23|XMLRPC| | ||
+ | |4|DOME|12|CUPOLA|24|INDI| | ||
+ | |5|WEATHER|13|FW|25|LOGD| | ||
+ | |6|ROTATOR|14|AUGERSH|26|SCRIPTOR| | ||
+ | |7|PHOT|15|SENSOR| | | | ||
+ | |8|PLAN|20|EXECUTOR| | | | ||
====== devices ====== | ====== devices ====== | ||
This will list the devices connected to rts2 | This will list the devices connected to rts2 | ||
+ | |||
+ | ====== lastimage ====== | ||
+ | This theoretically tells you which was the last image to be taken. Using the modifier ' | ||
+ | However if this fails (claims not a single image has been taken) | ||
+ | Looking at the status of the camera device will often state the last_image as a value. | ||
+ | |||
====== set ====== | ====== set ====== | ||
This will allow you to set values in rts2 devices. Modifiers are: | This will allow you to set values in rts2 devices. Modifiers are: | ||
' | ' | ||
+ | |||
+ | ====== status ====== | ||
+ | This will give the values of a specific module. Known modifier is: ' | ||
code/json.txt · Last modified: 2017/02/07 00:00 (external edit)